HomeLaboratoryFurnaces, Ovens & Incubators

Carbolite GCC -150 degC to +300 degC Gas Cooled Chambers

This range is now obsolete. Please return to the Furnaces, Ovens & Incubators Index.

A range of chambers using either liquid nitrogen or carbon dioxide as a cooling agent, making them ideal for low temperature testing with rapid temperature changes.

The normal working temperature range of the chamber is -60C to +200C. The maximum continuous working temperature is 200C, although this may be increased to 300C as an option. With the use of liquid nitrogen in place of the standard liquid carbon dioxide, the minimum temperature may be increased to -150C. Temperature uniformity throughout the chamber is better than +/-5C under steady state conditions, while temperature stability is better than +/-0.5C.

The outside case is constructed from zinc coated mild steel sheet and finished with light grey stoved epoxy powder paint. The internal chamber and air guides are fabricated from 304 grade stainless steel. Externally welded seams on the chamber prevent moisture from entering the insulation when the chamber is at sub-zero temperatures. The combination of high quality ceramic fibre and mineral wool blanket insulation ensures a safe outer case temperature.

Chamber access is via a single hinged door which opens to give access to the full chamber width. All temperature and power control equipment is housed in a control panel mounted on the right hand side of the chamber.

Heating is provided by mineral insulated metal sheathed elements; the low surface watt loading of the elements ensures that they have a long and reliable life. The chamber temperature is sensed by type 'K' thermocouples. The temperature is controlled either by a Eurotherm 2416CC programmer with 8 segments or a Eurotherm 2408CP 16 segment programmer.

Power to the heating elements is controlled by a thyristor based solid state relay. The relay works in the fast cycle zero voltage switching mode to ensure good power control and to reduce the generation of radio frequency interference.

Under/over temperature protection is recommended; if a fault causes the set temperature to be exceeded, then the Eurotherm 2132 on/off controller and safety contactor will isolate the elements and solenoid valve from the supply.

Cooling is provided by the injection of either liquid carbon dioxide or liquid nitrogen. The cool channel of the Eurotherm controller switches the direct injection solenoid valve. For liquid carbon dioxide, a 2 metre length of flexible high pressure hose is supplied to connect directly to the CO2 cylinder. A bursting disc is fitted in the pipework to prevent excessive pressures building up in the pipes. The carbon dioxide cylinder must be fitted with a dip tube so that liquid CO2 is supplied to the chamber. For liquid nitrogen, a 2 metre length of insulated flexible stainless steel pipe is supplied to connect directly to a self pressuring dewar. Pressure relief valves are fitted to prevent any build up of excess pressure in the pipework.

The chamber is fitted with a motor/fan unit and an air guide system to circulate the air within the chamber. The fan is mounted at the rear of the chamber and the air flow is horizontal through the chamber from left to right.

  Chamber capacities of 30, 60, 120 & 200 litres
  Minimum temperature of -60 degC is achieved with the use of liquid carbon dioxide
  Minimum temperature of -150 degC is achieved with the use of liquid nitrogen
  Maximum operating temperature 200 degC (300 degC available as an option)
  Cool down time from ambient to -60 degC is only 12 minutes
  Heat up time from ambient to +200 degC is only 26 minutes
  Temperature uniformity is better than +/-5 degC under steady state conditions
  Polished stainless steel inner chamber
  Externally welded seams prevent moisture entering the insulation when at sub-zero temperatures
  A motor fan unit & air guide system are fitted to circulate air within the chamber
  Heating is provided by mineral insulated metal sheathed elements
  Chamber access is via a single hinged side door, provding full and easy access
  The model shown features optional extras of viewing window and internal light

Options, including windows and cable ports, are available - please ask for details.

Models in this range:

GCC 30
GCC 60
GCC 120
GCC 200


Please note - Product designs and specifications are subject to change without notice. The user is responsible for determining the suitability of this product.

Back To Last Page



Chamber Furnaces Index

Tube Furnaces Index

Ashing Furnaces Index

Coal & Coke Furnaces Index

Precious Metals Index

Tritium Analyser (MTT)

Vacuum Tube Furnaces (HVTT)

Asphalt Binder Analyser (ABA)

Test Furnace for ISO 12981-1

Safe Air Dedicated Air Heater


Laboratory Ovens Index

Industrial Ovens Index

Clean Room Ovens (CR)

HT Clean Room Ovens (HTCR)

Coal Drying Ovens (CDLT & CDHT)

Application Specific Ovens Index


Furnace & Oven Controllers


Cell Block Rubber & Plastics Cable Ageing Ovens (SCBO)

Cooled Chamber (GCC)

Laboratory Incubators

Rapid Dental Zirconia Sintering (CDR 15/1)

Special Heat Treating Furnace (EVT)

Vacuum Tube Furnaces (HVT)

Want A Quotation?

We are open Monday to Friday, from 9.30 - 5.30 GMT.
Keison Global trading as:
Keison Products, VoIPon Solutions & 4Gon
keison VoIPon Solutions 4Gon Bitcoin Accepted Here Pay With Gold Globals